ダンプセミトレーラー

FLIEGL

Fine-grained steel welded construction with a slight "preload" in the neck area, turntable with replaceable 2" kingpin, outer frame slightly inclined, new design with "load-lock profile" for securing lashing straps, 24-ton, two-speed support winch, single-side operation, with straight lower section, without lateral thrust compensation. Note: Free support foot angle or free swivel radius to the rear approx. 1930 mm, extension ladder at the rear.
Door latch on the side, support wedges with holder, aluminum side impact protection, galvanized steel underrun protection, quarter panel fenders in front of the 1st axle and behind each axle, with anti-splash flaps behind each axle, rear impact protection, pallet stops on both sides approx. 15-20 mm high, in a bolted design, loading height reduced by approx. 15-20 mm, plastic toolbox with drawer and insert, w=650 / h=520 / d=670 mm.
Axles + Suspension
SAF disc brake axles, "axles/chassis laser-aligned" to reduce tire wear and fuel consumption, air suspension, 1st axle automatic lift axle, including forced lowering and start-up assistance, axle lift below the recommended ride height.
Braking System
2-line compressed air braking system, spring brake parking brake.
2 failsafe coupling heads in the front, without connecting line, EBS, electronic braking system with EBS socket in the front, without connecting cable. Note: with raise and lower valve, ride height in conjunction with lift axle, when the lift axle is raised, the loading height or total height increases by 50 mm.
Wheels and Tires
435/50 R19.5", steel rims.
Electrical System
24 Volt, multi-chamber lights, 2 white position lights in the front, 2 white/red side marker lights in the rear, 2 x 7-pin and 1 x 15-pin failsafe sockets in the front, without connecting cable.
Floor
Sieve plate approximately 30 mm thick, on longitudinal crossbeams for high point load capacity for forklift axle load up to max. 7100 kg.
Front Wall / Front Corner Posts
2580 mm high, corner posts made of steel in a box profile design, release device for side tarpaulin on the front wall.
Intermediate Posts
3 pairs of sliding posts, movable along the entire length, with 4 insertion pockets and a long pocket at the bottom.
3 pairs of post positions.
Insertion slats
5 rows of aluminum insertion slats + vario slats.
Rear Wall / Rear Corner Posts
Rear corner posts made of steel up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet.
Godpfozcmmzsx Apaeiu
Tarpaulin
Tarpaulin with welded-in horizontal and vertical straps, tensioning buckles made of stainless steel.
Roof
Fliegl Blitz sliding tarpaulin, rear end lift that can be folded up, with tarpaulin that can be slid from back to front, L-roof beam for the automotive industry, internal width between the roof beams approx. 2490 mm, tarpaulin color: white (in conjunction with a sliding tarpaulin that slides from the front without front rollers).
Approval Country / Signs
Germany, type approval according to EG 2007/46, 24/7 service hotline, Fliegl manufacturer certificate for structural strength according to EN 12642 XL, Fliegl manufacturer certificate for structural strength according to DL 9.5, pallet stops on both sides, approx. 20 mm high, loading height reduced by approx. 20 mm, Fliegl manufacturer certificate for load securing according to VDI 2700 sheet 12 ff. Pallet stops on both sides, approx. 20 mm high, loading height reduced by approx. 20 mm, prepared for license plate holder, single-row,

この広告は自動翻訳されています。翻訳ミスがある可能性があります。