幌付きオープントレーラー

FLIEGL Tandem-Plattform-Anhänger Durchlader

Custom-Made Transport Solution
Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs.

Type: TPS 118 Logistics Semi-Trailer

Chassis: Central Axle Trailer
Outer frame slightly inclined, new design with "Load-Lock profile" for securing tie-down straps
2-speed gear support leg at the front
Plastic toolbox
Platform height: 1080 mm
Coupling: Central axle trailer
Drawbar with tested 40 mm drawbar eye, logistics version
Drawbar mechanically adjustable in height via threaded spindle, below floor level, max. adjustment range 200 mm
Drawbar mechanically adjustable in length from approx. 1950 - 2300 mm, can be mechanically locked at approx. 50 mm intervals, drawbar length set to approx. 2100 mm
Axles & Suspension
SAF/BPW axles, selectable by the manufacturer
"Axle/chassis laser-aligned" to reduce tire wear and fuel consumption
Air suspension
Braking System
2-line pneumatic braking system
Spring-loaded parking brake
Duomatic connection at the front, with connection line to the towing vehicle
24 Volt EBS, electronic braking system with EBS plug at the front, with connection cable
with raising and lowering valve
Vehicle - Driving Stability System
Wheels and Tires
4x 235/75 R17.5, brand selectable by the manufacturer
4x steel rims, factory silver
Electrical System
24 Volt, multi-chamber lights, yellow LED lighting on the sides
2 white position lights at the front
2 white/red side marker lights at the rear
1 x 15-pin plug at the front, with connection cable
Floor
Sieve-printed panels, approx. 30 mm thick, for high point load capacity
Platform length: approx. 7,300 mm
Superstructure
Front wall / corner posts at the front
Through-loading system with front portal doors, 2-leaf, each with 2 internal rotary bolt locks, corner posts made of steel, release mechanism for side tarpaulin
Ramp, approx. 2,400 mm wide, 1 x divided, approx. 350 mm long for resting on the tailgate, load capacity approx. 1,800 kg, incl. support for the tailgate (drawbar length then approx. 2100 mm, for tailgate length of 1800 mm, the coupling offset from the truck must be at least 20 to max. 240 mm). Note! Usable internal length is reduced by the ramp!
Side Walls
Center Rails
2 pairs of sliding rails that can be moved along the entire length, with 4 pockets and a long pocket at the bottom
Insert strips
5 rows of wooden insert strips (in combination with side walls, 4 rows)
Rear Wall / Corner Posts at the Rear
Corner posts at the rear made of steel, extending to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet
Rear portal doors, 2-leaf, each with 2 internal rotary bolt locks
Tarpaulin
Tarpaulin with welded-in horizontal and vertical straps
Tensioning fasteners made of stainless steel
Customer lettering on side tarpaulins and rear portal possible
Roof
Sliding tarpaulin, rear end lift that can be folded up, with the tarpaulin sliding from back to front, tarpaulin color: white
Optimal rain gutter at the rear, above at the end beam, above the doors
Country of Registration / License Plates
Germany
with Dekra approval and certificate (according to §13 EG - FGV)
Fliegl manufacturer certificate for the structural strength of the superstructure according to EN 12642 XL
Hfjdjzcp E Tspfx Af Ejh
prepared for single-line license plate holder
Reflective strips: white, continuous on the bottom of the side tarpaulin and at the top in the corners
Reflective strip

この広告は自動翻訳されています。翻訳ミスがある可能性があります。