低床セミトレーラー

FAYMONVILLE Multimax Satteltieflader (1+3) - hydr. gelenkt

You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. The following is an excerpt from the equipment list. A complete equipment list is available upon request.

SWAN NECK
Swan neck in SNT design to optimize the loading area length, length approx. 3,700 mm, with a bevel at the rear of approx. 1,000 mm x 10°. For semi-trailer: 4 x 2, 6 x 2, and 6 x 4.
- Steel front wall, plug-in, approx. 400 mm high
- 3 kW electro-hydraulic unit for controlling the hydraulic operations, with the exception of hydraulic winches.
- 1 pair of plug-in aluminum side walls on the swan neck, approx. 400 mm high, in anodized finish.
- 1 plug-in aluminum rear wall on the swan neck, approx. 400 mm high, in anodized finish.
- 2-inch kingpin
- Mounting area in the rear section of the swan neck for aluminum approach ramps.
- Round NATO socket on the connection strip at the front (Maeler & Kaege VG 96 917)

LOADING AREA
Extendable loading area, length approx. 8,800 mm, with a bevel at the rear, approx. 500 mm x 10°. A recess in the loading area extends into the bevel to accommodate the excavator arm, approx. 3,850 x 750 x 210/290 mm (L x W x H). Pneumatic locking system with tapered locking pin and reinforced locking positions. The supply lines are protected in the extendable beams and automatically adjust to the respective loading area length.
- TPMS tire pressure monitoring system according to ECE R 141.
- BPW axles and suspension, 1st axle with steered trailing arm, all other axles with hydro-mechanical forced steering.
- 1st axle with electro-magnetic reverse lock via reverse gear and can be manually activated.
- Technical axle load: 12,000 kg each
- Air suspension with lifting and lowering valve.
- Tires 245/70 R 17.5 3PMSF, twin tires. Manufacturer of our choice.
- Locking of the loading area with tapered welded-on locking profiles every approx. 250 mm.
- 1 intermediate table, approx. 300 mm wide, for the extension tube with a large cross-section.
- Extendable widening elements (galvanized) by approx. 230 mm per side (without wooden planks).
- Wheel arches with square climbing strips, approx. 15 x 15 mm in front of the axles, continuously open up to the transverse support of the swan neck, approx. 700 x 410 mm (W x D).
Dkodpfxetx Nwnj Ac Tet
- Wheel arches with square climbing strips, approx. 15 x 15 mm between the 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D).
- Control valves for the hydraulic ramps on the right side of the vehicle.
- Steering from the front and rear can be operated via a cable remote control, with single-axle control, without installation in the semi-trailer.

HYDRAULIC LOADING RAMPS DR-15/60-900-4350-KG-HV-M
A pair of two-part steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm. The surface of the large ramp section is divided into two: sheet metal surface with square climbing strips approx. 15 x 30 mm every approx. 200 mm on the outside and rubber surface on the inside. Hydraulically folding ramp tips, ramps can be individually moved outwards by approx. 235 mm and inwards by approx. 215 mm hydraulically. Maximum load and approach angle according to the technical data sheet: C465501
- Rubber floor Super Grip approx. 25 mm and sheet metal floor approx. 5 mm as additional reinforcement on the bevel of the loading area.

BRAKING SYSTEM
Braking system from WABCO EBS-E according to EU regulations. Without connection cable to the semi-trailer tractor.

LIGHTING

この広告は自動翻訳されています。翻訳ミスがある可能性があります。