作業用プラットフォーム付きセミトレーラー

ES-GE 5-Achs-Ballastauflieger

You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website.
Excerpt from the equipment list.
Complete equipment list available upon request.

Chassis
* Welded construction made of high-quality steel profiles with continuous profile crossmembers
* Designed for high point loads
* Outer frame made of UNP steel

Fifth Wheel Coupling
* 2-inch kingpin

Under-ride Protection
* Compliant with EC standards, bolted design

Side Under-run Protection
* Compliant with EC standards

Landing Gear
* With single-side operation on the right
* Support load approx. 66 t / lifting capacity approx. 24 t.

Axles
* 5 x 10 t air suspension axle assembly
* Manufacturer: SAF
* With drum brake approx. 400x200 mm
* ABS, AGS
* Wheel connection centrally mounted, 10-hole with ET 0
* Total air suspension travel approx. 200 mm
* Of which lifting approx. 140 mm and lowering approx. 60 mm
Knedpfx Asz Dmndepdeb
* Control via rotary slide valve with detent function

Steering
* 1 axle with trailing steering
* 2nd axle fixed
* 3rd, 4th and 5th axles with forced steering via tie rod
* Lubrication points of swivel bearing centrally located outwards
* Axle lift: first and second axles automatically liftable
* With additional shutdown on the chassis

Braking System
* Two-circuit compressed air braking system compliant with EC with EBS and RSS
* Automatic load-dependent regulation
* Manufacturer: Wabco.
* Spring-loaded cylinders as parking brake
* Interchangeable secured coupling heads firmly mounted on the front cross member
* Without connecting line to the tractor unit
* Aluminum air tank

Tires
* 10x 445/65 R22.5 164J on rim 14.00 x 22.5 ET 0
* Manufacturer of our choice
* TPMS: Tire pressure monitoring system TPMS according to ECE R141
* With data transmission to the tractor unit

Fenders
* Compliant with EC standards, 1st axle at the front, 2nd axle at the rear
* 3rd, 4th and 5th axles each one 1/4 PVC fender at the front and rear
* Rear fender with mud flaps.

Load securing
* 5 pairs of folding lashing rings
* Evenly distributed (tensile force approx. 24.5 t)
* 11 pairs of hook plates welded into the outer frame (tensile force approx. 3 t)
* 10 pairs of lashing rings in the outer frame on the side, evenly distributed (tensile force approx. 10 t)
* Recess pockets: - 10 pairs of recess pockets recessed in the outer frame
* 6 pairs of recess pockets recessed in the floor (on the outside of the longitudinal beam)
* Stake pockets: - 16 pieces of galvanized stake pockets, approx. 80x80x8 mm, approx. 850 mm usable length (with locking mechanism)
* Stake magazine: one magazine for 8 pieces each on each side in front of the front wall
* Stake pockets approx. 80/80 mm

Front Wall
* Bolted corner stakes with a steel approach plate over the entire width and height.

Floor
* Approx. 28 mm Z-hardwood floor recessed in the outer frame flush

Lighting System
* Compliant with EC standards, 24 volt with multi-chamber lights
* LED side marker lights
* LED position lights white at the front
* LED outline lights at the rear
* License plate lights. 1x15 and 2x7-pole. Plug connection on the front cross member

Equipment
* Outrigger with holder, double
* Warning sign according to ECE 70
* Work lights on the lamp carrier (switched via reverse gear)
* Holder for rotating beacon at the rear (incl. rotating beacon)
* One climbing ladder each side fixed including pluggable climbing aid -
* Smart Board
* Sticker "Vehicle swings out"
* Sticker "Center of gra

この広告は自動翻訳されています。翻訳ミスがある可能性があります。